	USB-ML-Universal USB Multilink Universal Debug Probe for ARM® devices and 8/16/32 bit devices(software sold separately) FEATURES: Support device：Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, STMicroelectronics' SPC56, and ARM devices . USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the USB interface. Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target). Target Voltage:1.8V-5.25V Supports JTAG daisy chaining of multiple ARM MCUs. Pipelined programming algorithms for some Power Architecture families that dramatically increase programming speed. ARM device support includes both the JTAG and SWD protocols. Includes USB cable, Type A Male to Type B Male, 6-ft. Auto-frequency detection + trimming capabilities for HCS08 devices. Auto-frequency detection for HC(S)12(X) devices. Generates programming voltage on RESET line for RS08 devices. USB-ML-UNIVERSAL, Rev. E or later requires this RS08 adapter to allow the user to communicate with NXP's RS08 devices. Note: Multilink debug probes do not include software, as there are myriad options regarding the device architecture and utility of software that the user might require.

	USB-ML-Universal-FX USB Multilink Universal FX High-Speed Debug Probe for ARM® devices and 8/16/32 bit devices(software sold separately) FEATURES: Support device： Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, STMicroelectronics' SPC56, MPC5xx/8xx, HC16, 683xx and ARM devices . High-speed USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the USB interface. Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target). Can be used to power target MCU. Target Voltage:1.8V-5.25V Target Frequency: 16Khz-50Mhz (applies to HCS08, RS08, CFV1, S12Z, or HCS12X only) Supports JTAG daisy chaining of multiple ARM MCUs. Pipelined programming algorithms for some Power Architecture families that dramatically increase programming speed. I/O line clamping for added protection Auto-frequency detection + trimming capabilities for HCS08 devices. Auto-frequency detection for HC(S)12(X) devices. Generates programming voltage on RESET line for RS08 devices. ARM device support includes both the JTAG and SWD protocols Note: Multilink debug probes do not include software, as there are myriad options regarding the device architecture and utility of software that the user might require.

	CYCLONE-LC-UNIV Production Programmer and Debug Probe for ARM® devices and NXP 8/16/32-bit devices Support device： Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, HC08, MPC 5xx/8xx, STMicroelectronics' SPC56,ARM Cortex ,and STM8(with STM8 adapter),Infineon. Standard Cyclone Features: Stand Alone Programming - Program targets with a PC or without a PC Powerful Automation Control - PC based SDK, Console, and GUI Control, Gang Programming, Dynamic Data Programming Multiple Communications Interfaces- USB 2.0, Ethernet, and Serial interfaces Touchscreen LCD Display - Easy to use touch screen interface with remote access Target Power Management- Ability to provide and switch power to a target Auto-Counting & Shared Serial Numbers - Programming can incorporate sophisticated serialization Ethernet Based Debugging- Compatible with many development IDEs On-Board Storage - Encrypted internal memory, 16MB, 8 images Programming Control Port -10-pin port can launch programming, get status/results Optional upgrades for Cyclone LC: ProCryption Security - RSA/AES Encryption (Unique ImageKeys Safeguard Valuable IP) - Programming count/Date limits, etc. (Exercise Control Over Remote Operations)

	CYCLONE-FX-UNIV Advanced all-in-one program/debug/test interface for many ARM Cortex & NXP 8/16/32-bit devices. Support device： Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, HC08, MPC 5xx/8xx, STMicroelectronics' SPC56,ARM Cortex , and STM8(with STM8 adapter),Infineon ,Renesas（with Renesas adapter） Standard Cyclone Features: Stand Alone Programming - Program targets with a PC or without a PC Powerful Automation Control - PC based SDK, Console, and GUI Control, Gang Programming, Dynamic Data Programming Multiple Communications Interfaces- USB 2.0, Ethernet, and Serial interfaces Touchscreen LCD Display - Easy to use touch screen interface with remote access Target Power Management- Ability to provide and switch power to a target Auto-Counting & Shared Serial Numbers - Programming can incorporate sophisticated serialization Ethernet Based Debugging- Compatible with many development IDEs Programming Control Port -10-pin port can launch programming, get status/results Cyclone FX Advanced Features: High Speed Programming Target - Download rates reaching 75 Mbits/s Larger On-Board Storage - 1+ Gigabyte of encrypted internal memory stores 200+ programming images External SDHC Memory - External memory via SDHC Card Port Advanced Testing Feature - Run Tests Prior to Programming Target Current and Voltage Measurement ProCryption Security - RSA/AES Encryption (Unique ImageKeys Safeguard Valuable IP) - Programming count/Date limits, etc. (Exercise Control Over Remote Operations)

	PROG-HL-CFZ (former PROGCFZ) ColdFire Flash/EEPROM Programmer Hardware License PROGCFZ BDM Programmer allows program/reprogram external flash devices in-circuit, via P&E's a 26-pin BDM connector on the target system. Program Verify Blank check Upload Display Erase

	ICD-HL-CFZ (former ICDCFZ) ColdFire In-Circuit Debugger Hardware License Full-speed in-circuit emulation Breakpoints with counters on the Nth execution Variables window showing many data types Realtime execution as well as multiple tracing model Startup and Macro files for automating the debug process Context-sensitive help for all commands Timing measurement and execution count functions Support for symbolic register files Full assembly source-level debugging C source-level debug support

	LIC-CYC-PROCRYPTION Cyclone LC Protected and Encrypted SAP Image Activation License It allows users to place protection on their programming images to restrict image use by date range or number of programs allowed. It also allows users to create RSA/AES encrypted programming images that use their own uniquely generated ImageKey. These images may only be used to program targets on Cyclones that are pre-configured with this unique ImageKey. This license keeps the user securely in control of both their IP and the programming process. Restrict Image Use Encrypted (eSAP) Programming Images Encryption is Easy To Implement and Manage

	SDCARD 32 GB Encryped SDHC Flash Card for Cyclone FX This allows users to add expandable and easily swappable storage for their programming images. Adding one or more SD cards to your programming setup can give you added flexibility, while encryption helps keep your IP safe. An SD card can easily be moved from Cyclone to Cyclone. Our 32GB Encryptyed Cyclone SDHC Card is pre-formatted, tested, and certified to work with CYCLONE FX programmers. The SDHC port features are not available on Cyclone LC.

	CPRO_PWRSUPPLY Cyclone Power Supply Replacement Part Input - 100-240V, 50-60Hz, 0.48A Output - 5.9V, 3.0A, 17.7W, Center positive 58.25 inches (148cm) cable length Barrel connector - 5.5mm outer diameter, 2.5mm inner diameter 5 interchangeable international adapters

	CABLE_CF_Adapter 26-pin Synchronous ColdFire Ribbon Cable Adapter Note: The previous version of the adapter integrated a ribbon cable. The current version does not integrate the ribbon cable, it should be provided by the user. Synchronized debug communication signals are required for a few of the older ColdFire devices. This 26-pin synchronous adapter has integrated electronics to synchronize the ColdFire debug communication signals to the PSTCLK signal generated from a ColdFire target. The legacy USB-ML-CFE Multilink does not require this adapter cable as it inherently includes both synchronous and asynchronous circuitry. Designed for the following architectures: NXP ColdFire MCF5272 NXP ColdFire MCF5206(E) Designed to work with: Multilink Universal Multilink Universal FX Cyclone_LC Universal Cyclone_FX_Universal CAB_RIBBON_26-PIN CAB_RIBBON_26-PIN_FF

	CAB_RIBBON_26-PIN 26-Pin Ribbon Cable for ColdFire

	CAB_RIBBON_26-PIN_FF 26-pin female-to-female ribbon cable for ColdFire V2/3/4 26-pin female-to-female ribbon cable for ColdFire V2/3/4 devices. Please note that this ribbon cable cannot be used with devices that instead require a synchronous cable adapter, such as the MCF5272, MCF5206, and MCF5206E.

	PKG-HL-CFZ ColdFire Development Package Hardware License PROG-HL-CFZ Flash/EEPROM Programmer ICD-HL-CFZ In-Circuit Debugge WinIDE Windows Integrated Development Environment REGCF Register File Viewer/Editor

	Cyclone Automated Control Package(Legacy) Cyclone Automated Control Package with Dynamic Link Library (DLL) Multiple Cyclone Control Error Detection Dynamic Data Programming Image Maintenance Download the Basic Edition Package at no cost!

	Cyclone MAX （Discontinued） Stand-Alone Programmer and Hardware Debug Interface for ColdFire V2/V3/V4, Power MPC5xx/8xx, Qorivva MPC55xx/MPC56xx/MPC57xx & STMicroelectronics SPC56, Kinetis ARM® processor-based MCUs (includes L-Series), DSC , and MAC7xxx ARM® processor-based MCUs. The Cyclone MAX programmer has been discontinued. PEmicro's current generation CYCLONE and CYCLONE FX programmers are the official replacement parts. Within each type there are two models of Cyclone, one that supports ARM devices, and one that supports ARM devices plus many NXP 8/16/32 bit architectures.

	USB-ML-CFE （Discontinued） ColdFire 52xx/53xx/54xx BDM Interface (RoHS Compliant)) The USB-ML-CFE (USB ColdFire Multilink) has been discontinued. The recommended replacement part is the all-in-one Multilink Universal. Most software products will support the Multilink Universal transparently. Older software may need to be patched so that it will natively work with the latest Cyclones and Universal Multilinks.

	CABLE_CF (Discontinued) ColdFire BDM Interface (Parallel Port, 5V) Replacement probes for the CABLE_CF include the USB-ML-UNIVERSAL and USB-ML-UNIVERSAL-FX. For a production environment, we recommend the CYCLONE-FX-UNIV .

	CABLE_CFLV (Discontinued) ColdFire BDM Interface (Parallel Port, 3.3V) Replacement probes for the CABLE_CFLV include the USB-ML-UNIVERSAL and USB-ML-UNIVERSAL-FX. For a production environment, we recommend the CYCLONE-FX-UNIV .

	CASM Command-Line Assembler Command-Line Assembler Macro support S19 objects Conditional assembly Include files Full listing control with cycle counter

	Unit Library SDK for ColdFire V1 and V2/V3/V4 ColdFire Cable Interface Library Routines The package includes both C/C++ and Delphi example routines . The package consists of an interface DLL and sample code。 The C and Delphi modules in the ColdFire Hardware Interface Library Routines come as source code; The library is very useful for building your own production line testers. The demo programs show you how to initialize the interface, program registers, download code and step through code. Starting with these programs it is easy to customize them to your specific requirements. Key Features： Works with ColdFire architectures V2/V3/V4 through P&E's USB-ML-Universal, Multilink Universal FX, CYCLONE-LC-UNIV, CYCLONE-FX-UNIV Hardware Interfaces Provides Interface to Background Debug Mode Included in the package are C/C++ and Delphi modules Source and executables provided for both C and Delphi demos Number of functions in the library - 36 Compilers supported: UNITCFZ and UNITCFZ_DIST: MicrosoftVisual C++ 5.0 or greater, Delphi 2.0 or greater,Development platform: Windows 32-bit, Windows 64-bit (XP, Vista, 7,8,10) UNITCFZ library is very useful for building custom test, calibration, and update applications

	WINIDE ColdFire Windows Integrated Development Environment WinIDECF allows you to run external programs - including assemblers, C-compilers, debuggers, and flash programmers - in one environment, with a single hotkey for each. WinIDE comes installed with P&E's CASMCF assembler. Editor features include: Fully Reconfigurable Allows execution of external programs On-screen help Assembler features include: Macro support S19, HEX, IEEE695 objects Conditional assembly Include files Full listing control with cycle counter