Cyclone PRO
Hardware Debug Interface and Stand-Alone Programmer

• Support Freescale 68HC08, 68HCS08, 68RS08, 68HC(S)12(X) and ColdFireV1microcontrollers
• USB, Serial, and Ethernet interfaces(Windows 98/98SE/Me/2000/XP)
• Multiple programming images may be stored in Cyclone PRO’s memory.
• An LCD menu display, in conjunction with the status LEDs and buttons, allows stand-alone control and configuration of the Cyclone PRO
• Interactive in-circuit flash programming, debugging, and testing via a Host PC
• Stand-alone programming operation does not require a PC applicable to the use of production
• PC Controlled Stand-alone Programming，P&E provides A command line executable and A dynamically linked library (DLL)(PC Control Of Multiple Cyclones)
• Support CodeWarrior, Cosmic, IAR, P & E, and other development tools
• software and utilities:
Flash Programming

68HC08 Debugger

Cyclone PRO IP Setup Utility

Cyclone PRO Image Creation Utility

Cyclone PRO Launch Utility

BDM Multilink
BDM Multilink Interface

• Support Freescale 68HCS08,68 HC12,68 HC(S)12
• PC parallel port (DB25 female connector) (Windows 98/98SE/Me/2000/XP)
• Power from the target or Power supplier available for purchase
• Automatically calculates the speed and voltage of the target
NOTE: The Multilink cable is only recommended for development.

DEV912B32
68HC912B32 Development Board

• RS232 driver
• Enough pull-up resistors to configure the chip
• The 68F912B32 bus is completely free
• A 5-volt power supply

DEV9S12A256B
68HC9S12A256B Development Board

• RS232 driver
• Enough pull-up resistors to configure the chip
• The 68F912B32 bus is completely free
• A 12V center-negative power

DEV9S12DP256B
68HC9S12DP256B Development Board

• Two RS232 driver
• Enough pull-up resistors to configure the chip
• The 68F912B32 bus is completely free
• A 12V center-negative power
• Thru-hole development area
• Surface Mount Development Area,
• Full circuits, including CAN Tranceivers, for CAN0-CAN2

ICD12Z
68HC(S)12 In-Circuit Debugger

Based on Window98 / ME/NT/2000/XP for debugging code to give the user access to all on-chip resources。

• Paging support
• Hardware breakpoints for HCS12
• Full-speed in-circuit emulation
• Breakpoints with counters on the Nth execution
• Variables window showing many data types
• Realtime execution as well as multiple tracing model
• Startup and Macro files for automating the debug process
• Context-sensitive help for all commands
• Timing measurement and execution count functions
• Support for symbolic register files
• Full assembly source-level debugging
• C source-level debugging using ELF/DWARF v2.0 or ImageCraft v1.1 debug file format

PROG12Z
68HC(S)12 Flash/EEPROM Programmer

A command line version of the PROG12Z software which program/reprogram both internal and external flash devices in-circuit, via a six pin debug connector on the target processor system Programmer features include：

• Program
• Verify
• Blank check
• Upload
• Display
• Erase
• Show Data

USB-ML-12
68HC(S)12(X)/68HCS08/68RS08/Coldfire V1 BDM Interface (USB)

• Support Freescale 68HC(S)12(X)/68HCS08/68RS08/ColdFire V1
• USB port on a Windows 98SE/2000/XP/2003/Vista machine
• Draws power from USB interface
• Target Voltage: 1.6V-5.25V
• Target Frequency: 16Khz-50Mhz
• Auto-frequency detection + trimming capabilities for HCS08 devices.
• Auto-frequency detection for HC(S)12(X) devices
• Generates programming voltage on RESET line for RS08 devices.

Driver Download：Click here

WINIDE12Z
68HC(S)12 Windows Integrated Development Environment

allows you to run external programs - including assemblers, C-compilers, debuggers, and flash programmers - in one environment, with a single hotkey for each. WinIDE08Z comes installed with P&E's CASMHCS08 assembler

Editor features include:

• Fully Reconfigurable
• Allows execution of external programs
• On-screen help

Assembler features include:

• Macro support
• S19, HEX, IEEE695 objects
• Conditional assembly
• Include files
• Full listing control with cycle counter